日本三菱PC GSH2030R2原料
价格：26.00起
产品规格：
产品数量：
包装说明：
关 键 词：GSH2030R2原料,日本三菱PC
行 业：塑料 通用/工程塑料 工程塑料
发布时间：2021-06-15
The company mainly engaged in:
General plastic raw materials (GPPS, hips, ABS, as, MBS, PMMA, PP, HDPE, LDPE, LLDPE, EVA, PVC) engineering plastics raw materials (PET, PBT, LCP, PA6, PA66, PA46, PC, PC / ABS, PC / PBT, POM, PPA, PPS, PPO, peek, PTFE) thermoplastic elastomer (SBS, TPR, TPEE, Poe, TPU, TPO, TPV) and fiber adding, flame retardant, high temperature resistance and environmental protection grade of various new materials We can provide UL yellow card, SGS report and COA factory report as well as physical property table. Our market information is first-class and accurate. We provide after-sales technical support in time. Our company in good faith-based, customer first principle, will strive to face the global new and old customers to carry out business. Welcome to call or through QQ to our company for consultation and negotiation!
PC属中等耐磨材料（ 但比金属还是要好很多）。比尼龙、聚、氯化聚醚及PTFE差，但比ABS、聚砜、有机玻璃等好。在PC中加入某些填料可改善耐磨性，例如加入PTFE、玻纤等可降低摩擦系数和磨损量，提高PV值。PC的耐热性和耐寒性都很好，长期使用温度的范围较宽，可在-100~130℃范围使用，其负荷变形温度高（130~140℃），且受负荷影响小；脆化温度在-100℃以下，甚至在-180℃的低温下，也不会象玻璃那样破碎。PC没有明显的熔点，在220~230℃呈熔融状态。由于大分子链刚性大，其熔融粘度比其它热塑性塑料高得多.
Polycarbonate (PC) has good mechanical properties and good creep resistance, which is better than that of phthalamide and paraformaldehyde. Especially, PC modified by glass fiber has better creep resistance, so it can bear higher load at higher temperature and ensure dimensional stability. The main shortcomings of polycarbonate mechanical properties are easy to produce stress cracking, poor fatigue resistance, high notch sensitivity, no wear resistance and so on. PC has good high and low temperature resistance, good heat resistance at 120 ℃, and hot deformation temperature of 130 ~ 140 ℃. At the same time, it has good cold resistance, brittleness temperature is - 100 ℃, long-term service temperature is - 70 ~ 120 ℃. Moreover, its thermal conductivity and specific heat capacity are not high, its linear expansion coefficient is small, its flame retardancy is good, and it has self extinguishing property. As a weak polar polymer, PC has better electrical insulation although its electrical insulation is not as good as that of polyolefins. Because of its high glass transition temperature and low hygroscopicity, it can maintain good electrical properties under wide temperature and humidity conditions
PC is a kind of weak polar polymer. Although the electrical insulation of PC is not as good as that of polyolefins, it still has good electrical insulation. Because of its high glass transition temperature and low moisture absorption, it can maintain good electrical properties under a wide range of temperature and humidity conditions. Especially, its dielectric constant and dielectric loss are close to constant in the range of 10 ~ 130 ℃, so it is suitable for manufacturing capacitors. PC polycarbonate has certain chemical resistance. It is resistant to water, organic acid, dilute inorganic acid, oxidant, salt, oil, fatty hydrocarbon and alcohol at room temperature. However, it is eroded by alkali, amine, ketone, ester and aromatic hydrocarbon, and dissolved in trimethyl methane, dichloroethane, cresol and other solvents. Long term immersion in boiling water will also occur hydrolysis. In some chemical reagents, such as carbon tetrachloride, polycarbonate may cause stress cracking
Japan Mitsubishi PC model and grade introduction:
PC general pure PC: h-4000 H-3000 H-2000 s-3000 S-2000 S-1000 E-2000
PC flame retardant grade V-1: N-9
PC flame retardant grade V-2: fpr3000 fpr3500 fpr4500 ef50 ef51h efr3000 3200 3200h 2200
PC SAE fit grade PC: ml-200 ml-300 ml-400
PC lens grade: clv1000 cls1000 cls400 cls3400
PC gamma ray resistance: rs-3001r rs-1001r eb-3001r
PC optical diffusion level: ds-3002r 7011a ds-3002r 7031a ds-3002r 7051a dh-3002r efd2110u efd2230u
PC light reflection level: ehr3100 ehr3150 ehr3400 eh00 ehg2010r
PC light guide plate grade: hl-3000 hl-4000 hl-7001 hl-8000
Light guide grade for PC automobile: hl-3003 hl-3503
本公司长期供应美国RTP PC,德国拜耳PC,日本帝人PC,基础创新塑料(美国)PC,日本三菱工程PC,美国PC,韩国PC,韩三星毛织PC,货源稳定，质量保证，原厂原包，假一罚十。可提供SGS、ROHS、UL黄卡、MSDS、FDA、COA、PDF物性表等各项数据，公司有技术跟踪服务，欢迎来电洽谈！
自接到订单内发货，深圳，惠州，东莞，地区五百公斤以上包送货。一次购买数量500kg以上价格从优，欢迎各界朋友前来订购。
