价格：9000.00起
0
联系人：
电话：
地址：
特点 ◆全智能在线式,CPU微核芯片控制; ◆纯正弦波输出,确保马达绝无损害; ◆输入频率50HZ/60HZ自动识别; ◆超宽市电范围适应，关机智能充电; ◆低功耗,逆变效率高达95%以上; ◆逆变10分钟自动关机省电设计; ◆内置大容量免维护铅酸蓄电池, ◆可连续启动卷闸门18-20次 ◆完善的过载,欠压,短路,过充等保护功能. ◆遥控操作，挂墙式安装，体积小,重量轻。 ◆保修三年,内容包括：主板保修三年,电池保修一年。 温馨提示本产品为卷帘门电源，不带USB充电插口，图片仅供参考。 变频型三相应急电源 产品概述1、产品用途：CN-YJ/P三相变频动力应急电源是一种安装在建筑物内的备用电源装置。当建筑物发生 火灾、事故 和其他紧急情况导致市电断电时，三相应急电源可以为消防标志灯、照明灯、消防 泵、卷帘门和其他重要负 载提供第二路应急供电。随着建筑消防水平的提高，特别是高层建筑的增加，集中供电型应急电源已成为建筑物必备的消防设施。2、安装形式：落地式、分体式。3、备用时间：90分钟，国标型(可按设计要求配置备用时间)。规格范围规格范围2.2-400KVA三相输入3800V/AC落地式、分体式2.2-400KVA型号说明1、应急供电----市电中断或电压超出规定范围时自动提供380V、50Hz正弦波交流或直流应急供电，保证重要负载的正常工作。2、高性能----采用SPWM高频逆变技术，供电质量高，适应各种负载。3、高可靠----采用先进技术和冗余设计，有CPU控制，并选用优质元器件精心制造，性能稳定，可靠性高。4、保护完善----具有优良的输出过载保护、短路保护、电池反接保护、过放电保护等完善保护功能，抗误用能力强。5、界面友好----LCD显示工作状态、市电电压、输出电压，电池电压、电流、频率、负载率、故障等信息清晰明了；并且有声光故障报警、并具有故障消声等功能。6、充电能力强----机内装有采用自控充电技术的大电流电器，充电速度快，浮充电压稳定。7、结构简洁----机内功能部件采用模块化设计，结构简洁，维护方便。8、消防联动-----由消防中心集中监控和管理。9、智能电池管理----选用免维护电池和智能电池检测管理系统，加强电池监测，延长电池寿命和利用率。产品原理图 技术参数型号CN-YJ/P额定容量2.2-400KVA市电输入相数三相三线+PE电压380V±10%频率50Hz±5%应急输出电压380V/AC±15%波形正弦波波形失真THD≤5%(0-100%线性负载时)逆变效率≥90%过载能力≤120%额定电流正常工作>120%额定电流，正常输出约5秒后停止输出>120%额定电流或负载短路，限流输出约1秒后停止输出蓄电池类型密封免维护铅酸蓄电池额定电压492V备用时间90分钟(可按设计要求配置)充电时间20小时内可充满转换时间≤5秒(时间可满)保护应急状态过载保护，输出短路保护；电池反接保护；电池欠压保护等报警电池欠压、电池连接故障、充电器故障、持续过载、逆变器故障等环境温度-24℃-40℃环境湿度≤90%RH,不凝露海拔高度≤2500m噪音市电输出时静止无噪音，应急输出时≤55dB序号型号输出功率(KVA)电池电压(V)充电电流(A)电池数量(节)主机尺寸(mm)长×宽×高配置电池柜数量(90分钟)1CN-YJ/P-2.2KVA2.2192/4921.516/41400×750×1500电池在主机柜内2CN-YJ/P-3.7KVA3.7192/4921.516/41400×750×1500电池在主机柜内3CN-YJ/P-5.5KVA5.5192/492316/41400×750×1500电池在主机柜内4CN-YJ/P-7.5KVA7.5192/492316/41600×800×2200电池在主机柜内5CN-YJ/P-11KVA11192/492516/41600×800×2200电池在主机柜内6CN-YJ/P-15KVA15192/492816/41600×800×2200电池在主机柜内7CN-YJ/P-18.5KVA18.5192/4921016/41600×800×2200电池在主机柜内8CN-YJ/P-22KVA22192/4921016/41600×800×220019CN-YJ/P-30KVA30492541600×800×2200110CN-YJ/P-37KVA37492541600×800×2200111CN-YJ/P-45KVA454921041600×800×2200212CN-YJ/P-55KVA554921041600×800×2200213CN-YJ/P-75KVA754921041600×800×2200314CN-YJ/P-93KVA934921541600×800×2200315CN-YJ/P-110KVA×800×2200416CN-YJ/P-132KVA×800×2200617CN-YJ/P-160KVA×800×2200718CN-YJ/P-187KVA×800×2200719CN-YJ/P-200KVA2004922041600×800×2200820CN-YJ/P-220KVA2204923041600×800×2200821CN-YJ/P-250KVA2504923041600×800×2200922CN-YJ/P-280KVA2804923041600×800×22001023CN-YJ/P-315KVA3454924041600×800×22001124CN-YJ/P-400KVA4004924041600×800×220012外形尺寸单相/三相/三进单出 可根据实际要求 图纸定制生产；瑞祺能源，值得您信赖；厂家直供消防EPS应急电源、消防巡检柜系列等产品。EPS-1KVA /90分钟 为消防验收标准尺寸：1000*500*350电压：输入220V （380V） 输出220v回路：3个回路 按需可增加本产品是主机价格 电池另购买EPS消防应急电源该如何选择？选型原则是什么？EPS消防应急电源该如何选择？选型原则是什么？EPS emergency power supply, how to choose? Selection What are the principles? 一、负载容量选型原则:因电动机的启动冲击，与其配用的集中应急电源容量按以下容量选配。1、电动机变频启动时，应急电源容量可按电动机容量1.2倍选项配。2、电动机软启动时，应急电源容量应不小于电动机容量的2.5倍。3、电动机Y-△启动时，应急电源应不小于电动机容量的3倍。4、电动机直接启动时,应急电源容量应不小于电动机容量的5倍。5、混合负载中,大电机的容量若小于总负载容量的1/7.A load capacity of the principle of selection:Due to the impact of motor starting, its equipped with a centralized emergency power capacity in the following capacity matching.1, the motor frequency starts, emergency power supply capacity can be 1.2 times the option with the motor capacity.2, motor soft start, the emergency power supply capacity should be not less than 2.5 times the motor capacity.3, the motor Y-△ start, the emergency power supply should not be less than three times the motor capacity.4, motor direct start-up, emergency power supply capacity should be not less than five times the capacity of the motor.5, the mixed load, the maximum capacity of the motor is smaller than if the total load capacity of 1/7. 二、选型容量计算方法:1、柏克YJ系列或YJS系列用于带应急灯具负载时：（1）当负载为电子镇流器日光灯，EPS容量计算方法：EPS容量=电子镇流器日光灯功率和×1.1倍。（2）当负载为电感镇流器日光灯，EPS容量计算方法：EPS容量=电感镇流器日光灯功率和×1.5倍。（3）当负载为金属卤化物灯或金属钠灯，EPS容量计算方法：EPS容量=金属卤化物灯或金属钠灯功率和×1.6倍。Second, the selection of capacity calculation method:1, Burke YJ series or YJS series used with emergency lighting load:(1) When the load is electronic ballast fluorescent, EPS capacity calculation method: EPS capacity = electronic ballast fluorescent lamp power and × 1.1-fold.(2) When the load is inductive ballast fluorescent, EPS capacity calculation method: EPS capacity = inductive ballast fluorescent lamp power and × 1.5-fold.(3) When the load is a metal halide lamp or a metal sodium, EPS capacity calculation method: EPS capacity = sodium metal or a metal halide lamp power and × 1.6 times. 2、当YJS系列用于带混合负载时,EPS容量的计算方法:（1）当EPS带多台电动机且都同时启动时,则EPS的容量应遵循如下原则：EPS容量=变频启动电动机功率之和+软启动电动机功率之和×2.5+星三角启动机功率之和×3+直接启动电动机之和×5倍2, when the YJS series is used with mixed loads, EPS capacity calculation method:(1) When the EPS with multiple motors and are simultaneously activated, then the capacity of the EPS should follow the following principles:EPS capacity = frequency start the motor power and + soft start motor power of × 2.5 + star delta starter motor and the power of the motor is started directly × 3 + and × 5 times the （2）当EPS带多台电动机且都分别单台启动时(不是同时启动),则EPS的容量应遵循如下原则：EPS容量=各个电动机功率之和,但必须满足以下条件：※ 上述电动机中直接启动的大的单台电动机功率是EPS容量的1/7.※ 星三角启动的大的单台电动机功率是EPS容量的1/4.※ 软启动的大的单台电动机功率是EPS容量的1/3.※ 变频启动的大的单台电动功率不大于EPS的容量.※ 如果不满足上述条件,则应按上述条件中的大数调整EPS的容量,电动机启动时的顺序为直接启动在先,其次是星三角的启动,有软启动的再启动,后是变频启动的再启动.(2) When more than one motor and belt EPS were all single boot (not simultaneously start), then the capacity of the EPS should follow the following principles:EPS capacity = sum of all motor power, but must meet the following conditions:※ The motor started directly largest single motor power is the EPS capacity of 1/7.※ star delta starter largest single motor power is the EPS capacity of 1/4.Soft start ※ largest single motor power is the EPS capacity of 1/3.※ inverter startup largest single electric power less than EPS capacity.※ If not the above conditions shall be the maximum number of the above conditions the capacity to adjust the EPS, the motor startup sequence is started directly first, followed by the star-delta start-up, a soft start re-start, and finally the frequency conversion re-start. （3）当YJS系列EPS带混合负载时EPS应遵循如下原则：EPS容量=所有负载总功率之和,但必须中以下六条件,若不满足,再按照其中大的容量确定EPS容量.※ 负载中直接同时启动的电动机功率之和是EPS容量的1/7※ 负载中星三角同时启动电动机功率之和是EPS容量的1/4※ 负载中软启动同时启动的电动机功率之和是EPS容量的1/3※ 负载中变频启动同时启动电动机功率之和不大于EPS的容量.※ 同时启动的电动机当量功率之和不大于EPS的容量.电动机功率容量=直接启动的电动机总功率x5+星三角同时启动的电动机总功率x3+软启动同时启动的电动机总功率x2.5+变频启动且同时启动的电动机总功率若电动机前后启动时间相差大于1分钟均不视为同时启动。※ 同时启动的所有负载(含非电动机负载)的当量功率之和不大于EPS的容量。同时启动的所有负载的功率之和=同时启动的非电动机总功率×功率因数+电动机当量总功率。(3) When the YJS series EPS EPS with mixed loads should follow the following principles:EPS capacity = total power of all loads, but it must in the following six conditions, if not met, then the capacity determined in accordance with one of the largest EPS capacity.※ load directly activated simultaneously and that the EPS motor power capacity of 1/7※ star delta load and start the motor power and is EPS capacity of 1/4※ load soft start motor power of simultaneously started and is EPS capacity of 1/3※ load and start motor power inverter startup and not greater than the capacity of the EPS.※ started simultaneously equivalent power of the motor is not greater than the capacity of EPS.Motor power capacity = direct start of motor power x5 + star delta start simultaneously x3 + motor power soft-start and start the motor power x2.5 + inverter motor starts and the total power simultaneously startedIf the motor before start time difference than 1 minute are not regarded as the same time.※ started simultaneously all loads (including non-motor loads) of equivalent power is not greater than the capacity of EPS.Started simultaneously in all the power load and simultaneously start = total power × non-motor motor power factor + Equivalent total power.
