西门子0.37KW变频器6SL3210-5BB13-7UV1 西门子 资讯
价格：188.00起
功能
Feature
Comment
Connection and application macros
Sets groups of parameters to simplify commissioning
?Connection macros for connections
?Application macros for applications
Keep Running Mode
Single-parameter setting for a mode which keeps the motor going – enables
?Vdc_max controller
?Kinetic buffering
?Restart after fault
?Flying start.
?Disables alarms etc.
ECO mode
Economy mode – searches for most efficient rated point
Hibernation mode
Intelligent economy mode in idle state
PID controller
Integrated PID controller with auto-tuning function
Kinetic buffering (Vdc_min controller)
Retention of minimal DC voltage through regenerative energy for continued operation
Vdc_max controller
Automatic change of ramp down time/braking time
Imax controller
Automatic change of ramp up time to avoid overcurrent
Automatic restart
Automatic restart of drive once the power has been restored following a power failure. All faults are acknowledged automatically and the drive is switched on again
Flying restart
Allows the converter to be switched to a rotating motor
Energy consumption monitoring
Displays a simple estimate of energy or cost saved against use of a line-connected motor
50/60 Hz adaptation
Easy selection of operation with 50 Hz (Europe, Asia) / 60 Hz (USA)
V/f and V2/f
V/f: perfectly suitable for almost any application in which the speed of asynchronous (induction) motors is to be changed
V2/f: suited to loads with quadratic load curves, e.g. turbo machines such as pumps and fans
FCC
Maintains motor flux current for improved efficiency
Programmable V/f coordinates
Freely adjusts the V/f characteristics, e.g. torque behavior of the synchronous motor
JOG
Moves the motor to test the direction or moves the load to specific position. When the BOP switches to JOG mode, pressing the start button of the BOP will run the motor up to the JOG frequency.
Releasing the start button stops the motor
DC braking
Stops the motor which runs at constant speed and only comes to a standstill in longer time intervals, e.g. centrifuges, saws, grinding machines and conveyor belts
Mechanical holding brake control
The motor holding brake prevents the motor from undesirable turning when the converter is switched off. The converter has an internal logic to control an external motor holding brake
USS
Universal Serial Interface Protocol
Modbus RTU
Modbus RTU communication available via the RS485 link
Super torque mode
Big torque boost for starting high-inertia applications
Hammer start mode
A number of torque pulses at start-up to start difficult or "stuck" loads
Blockage clearing mode
Multiple-reverse function to clear blocked pumps
Simple parameter-based menu on internal or external BOPs
Easy selection for displaying values, editing parameters, converter setup
Simple text menu for setup
The parameter number will be shown as short text in the 7-segment LED display
Motor frequency display scaling
User settable display scaling for special applications i.e. rather than Hz, it shows application-specific values like "gallons per minute", "potatoes per hour", etc.
Customization of parameter defaults
Customers or OEMs can set their own special "permanent" defaults which can only be deleted in special mode
Converter status in case of a fault
Record the fault with running data
Complete motion control solutions from Siemens – SINAMICS V20 and SIMATIC
Siemens offers comprehensive solutions from a single source for general motion control applications with a selection of different SINAMICS application examples:
?Ready-to-run application examples, including wiring diagrams, parameter descriptions
?Sample configurations for connecting SINAMICS with SIMATIC, including hardware, software and wiring examples, installation instructions for the supplied S7 project, drive parameterization, and HMI sample projects- Correctly configured project, ready for operation
- Optimal leveraging of TIA advantages
Accessories
1
SINAMICS V20 Smart Access
Wireless commissioning, operation, and diagnostics with mobile device or laptop using web server module
2
SINAMICS V20 BOP
?Same function as the integrated BOP (Basic Operator Panel)
?Can also be used for remote mounting
?Values and setpoints are changed by rotating the wheel
?For distributed mounting with IP54 and UL Type 1 enclosure rating
3
SINAMICS V20 BOP Interface
?Connection between converter and BOP
?RJ45 interface is compatible with standard network cable
4
Standard network cable
?Cable not included in delivery
?You can use any standard network cable with standard RJ45 connector
5
SINAMICS V20 Parameter Loader
?Up to 100 parameter sets with parameter settings can be written from the memory card to the converter, or saved from the converter to the memory card
?The converter does not have to be connected to the line supply
6
SINAMICS SD card
?Memory card, 512 MB
?Standard SD cards up to 32 GB are supported
7
SINAMICS V20 I/O Extension Module
?Expansion of the 400 V converters with two digital inputs and two digital outputs (relay outputs)
8
Line filter
Improved EMC characteristics
9
Line reactor
?Reduces the harmonic current
?Improves the power factor
?Recommended if input current (rms value) is higher than the rated current of the converter
10
SINAMICS V20 Braking Module
?Shortens the deceleration ramp time
?Suitable for 230 V 1 AC and 400 V 3 AC
?Adjustable duty cycle from 5 % to 100 %
?For frame sizes FSAA, FSAB, FSAC, FSA, FSB and FSC
?FSD and FSE already have an integrated braking unit
11
Braking resistor
?Dissipates regenerative energy as heat
?5 % duty cycle as default setting
12
Output reactor
For longer motor cable
?230 V 1 AC: 200 m (shielded and unshielded)
?400 V 3 AC:- for frame sizes FSA to FSD: 150 m (shielded and unshielded)
- for frame size FSE: 200/300 m (shielded/unshielded)
13
Shield connection kit
?Shield connection
?Strain relief
14
Standard fuse
Recommended fuse corresponding to the IEC/UL standard
15
Circuit breaker
Recommended circuit breaker corresponding to the IEC/UL standard
-/gbadicf/-
