价格：999起
乐清市华产电气有限公司
联系人：刘云凡
电话：15888435838
地址：浙江省乐清市柳市镇电器城外围
Autonics编码器E40S6-10-3-T-24奥托尼克斯Autonics编码器 我公司专业代理 奥托尼克斯Autonics编码器 ● 体积小, 重量轻, 安装方便，可在狭小空间安装。 ● 外径Φ40mm ， 止口Φ20mm ，D 型切口，轴径Φ6mm. ● 适用于精密工作环境. ● 电缆侧出. ● 电源电压：5VDC ，12-24VDC ±5% ● 信号输出：A 、B 信号 A 、B 、Z 信号 A 、A 的反相信号、B 、B 反相信号, A 、A 的反相信号、B 、B 反相信号, Z 、Z 的反相信号。 ● 消耗电流: ≤120mA ● 输出波形: 方波 ● 载空比:0.5T ±0.1T ● 较大机械转速:6000rpm ● 防护: 防水, 防油, 防尘IP54 E40S6-10-3-T-24 The encoder ( encoder ) is a ** (such as a bit stream) or data are compiled, are available for conversion to communication, transmission and storage form of ** equipment. The encoder into angular displacement or linear displacement into electric **, the former is called encoder, which is referred to as the yardstick. According to the readout mode encoder can be divided into contact and non-contact two. Contact with brush output, a brush contact conductive or insulating area codes for the representation of state is " 1 " or " 0 "; non-contact accept sensitive element is a photosensitive element or the magnetic sensitive element, the photosensitive element to the photic zone and opacity area to represent code state is " 1 " or " 0 ", the " 1 " and "0" of the binary coded to the acquisition of physical ** into machine code can be read by the electric ** to the communication, transmission and storage. The encoder fault: refers to the encoder itself components failure, leading to its cannot generate and output the correct waveform. This case needs to replace or repair the devices inside the encoder. The encoder is connected cable fault: the failure probability is maximal, often encountered in repair, should be the priority factor. Usually encoder cable circuit, short circuit or bad contact, then the need to replace the cable or connector. Special attention should also be paid to whether it is due to the cable are not tightly fixed, caused loosening caused by welding or open circuit, and then need to clamp the cable. The encoder +5V power decline: refers to the +5V power supply is too low, usually not less than 4.75V, resulting in low reason is the power supply failure or power transmission cable resistance partial caused loss, it is necessary to repair or replace the cable power supply. The absolute encoder battery voltage drop: this kind of fault is usually the meaning clear alarm, then the need to replace the battery, if the reference position memory loss, must perform to return to reference point operation. The encoder cable shielding line missed or fall off: this introduces the interference **, the waveform instability, influence the accuracy of communication, must ensure that the shielding lines and reliable welding and grounding. The encoder is installed loose: this fault will affect the precision of position control, cause stop and mobile position deviation deviation, or even just a boot that produces a servo system overload alarm, please pay special attention to. This will make the pollution, grating ** output decline, must use cotton dipped lightly ethanol erase oil. [1] E40S6-10-3-T-24 编码器（encoder）是将信号（如比特流）或数据进行编制、转换为可用以通讯、传输和存储的信号形式的设备。 编码器把角位移或直线位移转换成电信号，前者称为码盘，后者称为码尺．按照读出方式编码器可以分为接触式和非接触式两种．接触式采用电刷输出，一电刷接触导电区或绝缘区来表示代码的状态是"1”还是“0”；非接触式的接受敏感元件是光敏元件或磁敏元件，采用光敏元件时以透光区和不透光区来表示代码的状态是"1”还是"0”，通过"1”和“0”的二进制编码来将采集来的物理信号转换为机器码可读取的电信号用以通讯、传输和储存。 ⑴编码器本身故障：是指编码器本身元器件出现故障，导致其不能产生和输出正确的波形。这种情况下需更换编码器或维修其内部器件。 ⑵编码器连接电缆故障：这种故障出现的几率 较高，维修中经常遇到，应是**考虑的因素。通常为编码器电缆断路、短路或接触不良，这时需更换电缆或接头。还应特别注意是否是由于电缆固定不紧，造成松动引起开焊或断路，这时需卡紧电缆。 ⑶编码器+5V电源下降：是指+5V电源过低， 通常不能低于4.75V，造成过低的原因是供电电源故障或电源传送电缆阻值偏大而引起损耗，这时需检修电源或更换电缆。 ⑷**式编码器电池电压下降：这种故障通常有含义明确的报警，这时需更换电池，如果参考点位置记忆丢失，还须执行重回参考点操作。 ⑸编码器电缆屏蔽线未接或脱落：这会引入干扰信号，使波形不稳定，影响通信的准确性，必须保证屏蔽线可靠的焊接及接地。 ⑹编码器安装松动：这种故障会影响位置控制 精度，造成停止和移动中位置偏差量**差，甚至刚一开机即产生伺服系统过载报警，请特别注意。 ⑺光栅污染 这会使信号输出幅度下降，必须用脱脂棉沾无水酒精轻轻擦除油污。[1]