价格：160起
汽车座椅加热北京暖世康有限公司
联系人：朱经理
电话：13021243672
地址：北京
Five Volume control with membrane switch seat heater
1. Composition
Two heating pads, one wire harness, one controller, one five volume control membrane switch.
2. Installation
(1) First, take off the cover of the seat, then fix the pads on the back and bottom of the seat separately, put the electrode of pads through the middle gap of bottom and back to under the seat evenly.. ready for connect with controller
(2) Plug-in the two plugs from controller to the two plugs from pads under the seat, fix the controller under the seat with bond strip, fix the loose or longer cables under the seat with bond strip too, lay the cable under the carpet to the underside of fuses holder, connect with power after the membrane switch sticked.
(3) Put the membrane switch along the side of the seat, which is the side that safety belt with socket, go along the right side of the driver, left side of the side-driver, go along under the seat slide, not above the seat slide, otherwise it may press and cut off the switch wire with running failure. Take away the protection paper on the back of the membrane, stick the membrane switch at the side of safety belt, main seat is at the side near to driver, side seat is at the side near to side-driver. Stick it with correct and solid, then you start connect the power cable.
(4) The connection of power cable, First, connect the black wire to the ground line, such the position where the screw nut contact with car to assure the good touch between black wire and car. If there is a screw nut on the car and there is paint on it, you should cut off the paint first then connect the black line under the nut, the black wire should be pressed solidly and no loose. Now you may connect for red wire, to find a wire which can transmit at least 10A current under the dashboard and the diameter is at least 0.06inch and the current is 0 while car is not working, or put the red wire at the position under the fuse socket which marked 10A. The way of finding such wire, turn the multimeter to 20V, switch on the mulitimeter, connect the black pen with ground line, red pen connect the point The place you connect to should not have a voltage when the car is not working. When the car is not working there is 0V on the screen, when the car is working the voltage should be at least 12V.That means this is the right place. You may start to run the system after the wire located and red wire fixed.
3. How to use
(1). Start the car first, press the membrane switch 6 times, the indicators will be changed according to this way, red indicator brighten up, green indicator brighten up, both red and green indicator brighten up, red indicator flash, green indicator flash, both indictor extinguish, it means the seat heater is running at 5 volume different temperature allocated.
(2). First time enter cab in winter, first press switch once, the temperature is set up in highest temperature, after heating up for some time, if you feel the temperature is too high, you may adjust down the temperature through pressing switch once by once.
(3). The heating system will be switch off automatically, when car extinguish, you can use heating system after car start.
4．Note
(1) Make sure all wires are connection in right place and solid, no press from seat rail, When installing the seat heater, beware of electrical conductive components, such as the hog rings or the metal seat frame, which may come in contact with the heating element creating a risk of short circuiting the entire system.
(2) Power cable should be connected fix and press tightly, membrane switch should be sticked in right place and solid, stick to the place which operate easily, such as the side of socket of safety belt.
五档膜开关汽车座椅加热系统
一.组成:
由一个控制器,一个膜开关,一条线和两个热片组成.
二.安装方法:
1.将座套取下来,把热片分别粘贴固定在座和靠背上,将热片电极从靠和座的中缝顺于座椅下面.等待与控制器对接.
2.在座椅下面将控制器上的两个插头与两片热片上的插座对插.把控制器用拉扣固定在座椅下面,一些长出来的散线也可以用拉扣固定在座椅下面.这时候将线缆平铺于汽车地脚下面,延续到汽车一排保险的下面,等膜开关贴好后再接电源.
3.将膜开关从座椅侧面,即有汽车保险带插座的那个 側面.主驾驶的右面,副驾驶的左面顺上来.穿过座椅滑轨的较下面顺上来.不要从滑轨上面顺上来,以免开关线被滑轨压断,影响使用.这时候将膜开关背面保护纸揭开,将膜开关贴于保险带座侧面,主座是靠近驾驶员的这一面相反的面,副座是靠近副驾驶人员的那面相反的面.主要是当保险带插到座里后,也便于按动调温膜开关.膜开关要贴正,贴牢.这时可以接电源线了.
4.电源线的连接:先将黑线接于汽车搭铁线上,如各处与汽车壳体相连的锣母下面,如果连接部位有绝缘漆,这时要把绝缘漆处理掉,保证黑线与壳体接触良好,黑线要压牢接好.不能松动.红线要接于电流大于10安的地方,如可接于大于10安保险座的座下面.也可接在线径大于一个平方的线上,无论接在哪,这一点当汽车熄灭后没有电流通过.汽车启动后才有电流通过.可用万用表找到这一点.将表打到20伏档位,汽车启动后,黑表笔接搭铁线,红表笔接测试点,这点有大于12伏的电压,熄灭后电压为零.这样这点就找到了.将红线压紧接牢.
三.使用方法:
1.先启动汽车,用手按动膜开关六次,开关上灯按照如下状态变化,红灯亮,绿灯亮,红绿灯都亮,红灯闪,绿灯闪,两只灯都灭.表示把座垫加热温度设定在五个不同温度.
2.冬季刚进入驾驶室时,先安一下开关,把温度设定在较高温,加热一段时间后,如觉得温度过高,可一下一下按动开关向下调温........
3.当汽车熄火后,加热自动关闭.汽车启动后才可使用加热.
四.注意事项:
1.线要接对位置,压牢接好,不要被座椅滑轨压到;热片要贴好压牢,拉环穿过热片时,不要与热片的黑色碳纤维接触,否则会段路,以免烧损座套.
2.电源线要接牢,压紧;膜开关贴正,贴牢,贴在方便操作的位置,如保险带插座侧面.